
1, 구멍 가이드 종이가 파손 되지 않도록 분해 한다
1, Disassemble the hole guide paper so that it does not break.

2, 구멍 가이드 종이를 커팅해 준다.
2, Cut the hole guide paper..

3,센터 펀치와 종이 가이드로 구멍의 위치를 확인한다.
3, Check the position of the hole with a center punch and paper guides.

4, 구멍을 만드는 드릴을 사용해라. (구멍 지름 4.5~5MMM)
4, Use the drill makes a hole. (Hole diameter 4.5 ~ 5MM)

5, 드릴을 이용해 3개의 구멍을 뚫는다.(홀 직경 4.5~5MMM)
5, Use the drill will drill three holes. (Hole diameter 4.5 ~ 5MM)

6, 너클 가드 후면 파츠에 드릴을 이용 하여 구멍 가공을 한다.(홀 직경 4.5~5MMM)
6, Drill holes in the rear part of the knuckle guard (Hole diameter 4.5 ~ 5MM)

7, 너클 가드의 볼트에 고무 스페이서를 넣어준다.
7, Put the rubber spacer in the bolt of the knuckle guard.

8, 전선 삽입후 조립해 준다.
8, Insert the wire and assemble it.

9, 후면에 너트를 이용 하여 고정 한다.
9, Use a nut to secure the rear face

10, 너클 가드 후면 파츠에 전선 삽입후 조립한다.
10, Insert the wire into the rear part of the knuckle guard and assemble it.

11, 후면에 볼트를 이용 하여 고정 한다.
11, Use a bolt to secure the rear face.


1, 구멍 가이드 종이가 파손 되지 않도록 분해 한다
1, Disassemble the hole guide paper so that it does not break.
2, 구멍 가이드 종이를 커팅해 준다.
2, Cut the hole guide paper..
3,센터 펀치와 종이 가이드로 구멍의 위치를 확인한다.
3, Check the position of the hole with a center punch and paper guides.
4, 구멍을 만드는 드릴을 사용해라. (구멍 지름 4.5~5MMM)
4, Use the drill makes a hole. (Hole diameter 4.5 ~ 5MM)
5, 드릴을 이용해 3개의 구멍을 뚫는다.(홀 직경 4.5~5MMM)
5, Use the drill will drill three holes. (Hole diameter 4.5 ~ 5MM)
6, 너클 가드 후면 파츠에 드릴을 이용 하여 구멍 가공을 한다.(홀 직경 4.5~5MMM)
6, Drill holes in the rear part of the knuckle guard (Hole diameter 4.5 ~ 5MM)
7, 너클 가드의 볼트에 고무 스페이서를 넣어준다.
7, Put the rubber spacer in the bolt of the knuckle guard.
8, 전선 삽입후 조립해 준다.
8, Insert the wire and assemble it.
9, 후면에 너트를 이용 하여 고정 한다.
9, Use a nut to secure the rear face
10, 너클 가드 후면 파츠에 전선 삽입후 조립한다.
10, Insert the wire into the rear part of the knuckle guard and assemble it.
11, 후면에 볼트를 이용 하여 고정 한다.
11, Use a bolt to secure the rear face.